Breaking discs

[the big wheel]

Lots of areas that would never be considered
To farm are dry so wondering what are good
Sod type discs? See some deep curved blades
Not sure if those cut as good as the others?

[Guest]

kello bilt is all you need
doesn't matter if its 30 years old

[blackpowder]

Depends if you're renting or buying.
My 225 kello too light to cut real hard stuff without a weight box. They make heavier models. Never changed a Kello bearing.
However, anything else and your fixing steady unless it's new. Wisheks you rent only but they're heavy.
Our Landoll will do sloughs etc in 3-4 passes but it's still awful expensive to run.
Discs are like sheep. Born to die.

[furrowtickler]

We have an old Allis Chalmers tandem disc
Works ok but it is getting very wore now .
Very hard to even get parts the past few years

[Taiga]

Have a 30’ Wishek 842 that has been very good, seen a lot of brush and rocks. Wishek’s are a lot heavier than Kello at over 1000lbs/ft. Kelly’s are good though.
The 22’ Wishek is the worst size, and is the size Flaman rents, because the wings are too short and so they don’t have the weight on the wings and they ride up and don’t penetrate as deep as the center main frame.

[jamesb]

We have rented disks in the past from Flamans etc and it works but always would have liked to have something handy for the old slough as it comes up. Our old 27 foot Case disk was great for normal field work but take it into a slough with rocks and your breaking blades constantly. Several years ago I finally found a Rome disk at a cheap price. Those old Rome disks are basically indestructible IMO. Our is only 12 feet but its great as fire guard unit and follows the combine quite a bit if needed (once). The amount of old rock piles in the bottom of sloughs that we discover when the disk goes over them is pretty common (lots of rocks in my parts). Ours came out of Nebraska on Big Iron auctions.

[Herc]

Kello 275 16’. Cheaper than wishek and will outlast anything else on ur farm. Like everything a new one 15 years ago was $20k. Now they’ll be $40k….and here’s the kicker, nothing has changed on them.

[Sheepwheat]

I’ll give you guys the good news if you want to hear it.

I have rented discs three times in the fall, to “retake” sloughs and put them back into production. Each time, it caused excessive rainfall, and it was a waste of my time and money.

But when you get those sloughs nice n black, it WILL rain, and do its best to fill them back up with water.

So good on y’all for giving it a whirl. Western Canada will thank you.

[the big wheel]

I’ll give you guys the good news if you want to hear it.

I have rented discs three times in the fall, to “retake” sloughs and put them back into production. Each time, it caused excessive rainfall, and it was a waste of my time and money.

But when you get those sloughs nice n black, it WILL rain, and do its best to fill them back up with water.

So good on y’all for giving it a whirl. Western Canada will thank you.

That could be 100% correct but I did a few
So called sloughs last fall with an older deep tiller
And used neighbours light disks that ended
Up a work project in replacing bearings.
But those areas at least had something
That resembled a crop. It didn’t make a whole
Lot of money as not a big area but at least i
Had something to look at all year that I wasn’t
Depressed about. Lol
But you could be right could be all for nothing
But if my disking holes causes rain I m all in!!
Might not fit your area I understand.

[workboots]

The 26ft Wishek has been a good unit on our farm. It’s chewing up some low spots right now that have been unattainable for 20 some years. It’s a nice feeling when your gaining ground, especially if you try to keep your mind off the reality that the lifeblood of your business went extinct from these low places and they might be the only legitimate crop next season.
We did make the mistake of overgreasing the greasable bearings on the wishek and pushing out some seals. It’s a real dusi of a job changing them out. The Kello-bilt disc we had for some time had an oil bath bearing that was bulletproof but it was too light for a lot of jobs.